View ICPL2611_319907.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

www..com
ICPL2611
HIGH CMR, VERY HIGH SPEED OPTICALLY COUPLED ISOLATOR LOGIC GATE OUTPUT
APPROVALS l UL recognised, File No. E91231 DESCRIPTION The ICPL2611 optocoupler consists of a GaAsP light emitting diode and a high gain integrated photo detector to provide 2500Volts RMS electrical isolation between input and output. An enable input allows the detector to be strobed. The output of the detector I.C. is an open collector Schottky clamped transistor. The ICPL2611 has an internal shield which provides a common mode transient immunity specification of 10000V/s typical.This unique design provides maximum ac and dc circuit isolation while achieving TTL compatibility. The coupled parameters are guaranteed over the temperature range of -40C to +85C, such that a maximum input signal of 5mA will provide a minimum output sink current of 13mA(equivalent to fan-out of eight gates) FEATURES l High speed - 10MBit/s l High Common Mode Transient Immunity 10kV/s typical l Logic gate output l ICPL2611 has improved noise shield for superior common mode rejection l Options :10mm lead spread - add G after part no. Surface mount - add SM after part no. Tape&reel - add SMT&R after part no. APPLICATIONS l Line receiver, data transmission l Computer-peripheral interface l Data multiplexing l Pulse transformer replacement
OPTION SM
SURFACE MOUNT
2.54 1 6.9 6.3 2 3 4 1.3 9.7 9.1
Dimensions in mm
VCC
8 7 6 * 7.62 4.0 3.6 0.5 3.3 0.3 15 Max 5GND
* NOISE SHIELD
0.5
1.3
TRUTH TABLE INPUT ENABLE OUTPUT H H L L H H H L H .com L L H
A 0.1F bypass capacitor must be connected between pins 8 and 5 ( See note 1)
DataShee
ABSOLUTE MAXIMUM RATINGS (25C unless otherwise specified) Storage Temperature -55C to + 125C Operating Temperature -40C to + 85C Lead Soldering Temperature (1/16 inch (1.6mm) from case for 10 secs) 260C INPUT DIODE Average Forward Current Reverse Voltage DETECTOR Enable Input Voltage ( VE ) (not to exceed VCC by more than 500mV) Supply Voltage(VCC ) (1 minute maximum) Output Current ( IO ) Output Voltage ( VO ) Collector Output Power Dissipation 5.5V 7V 50mA 7V 85mW 50mA 5V
OPTION G 7.62
1.2 0.6 10.2 9.5
1.4 0.9
0.3 10.16
ISOCOM COMPONENTS LTD Unit 25B, Park View Road West, Park View Industrial Estate, Brenda Road Hartlepool, TS25 1YD England Tel: (01429)863609 Fax : (01429) 863581 e-mail sales@isocom.co.uk http://www.isocom.com .com
30/7/03
ISOCOM INC 1024 S. Greenville Ave, Suite 240, Allen, TX 75002 USA Tel: (214) 495-0755 Fax: (214) 495-0901 e-mail info@isocom.com http://www.isocom.com
DB91019-AAS/A2
DataSheet 4 U .com
www..com
ELECTRICAL CHARACTERISTICS ( TA= 0C to 70C Unless otherwise noted ) PARAMETER High Level Output Current SYM DEVICE IOH VOL 0.35 MIN TYP* MAX UNITS 100
A
TEST CONDITION VCC = 5.5V, V O = 5.5V IF = 250A, VE = 2V VCC = 5.5V, IF = 5mA VE = 2V IOL (sinking ) = 13mA VCC = 5.5V, V O = 0.6V VE = 2V, IOL = 13mA VCC = 5.5V, IF = 0mA VE = 0.5V VCC = 5.5V, IF = 10mA VE = 0.5V VCC = 5.5V, V E = 2V VCC = 5.5V, V E = 0.5V VCC = 5.5V, IF = 10mA VCC = 5.5V, IF = 10mA IF = 10mA, TA = 25oC IR = 10A, TA = 25oC VF = 0, f = 1MHz IF = 10mA R.H.equal to or less than 50%, t = 1min, TA=25C R.H.=45% t = 5s, TA= 25C VI-O = 3000V dc VI-O = 500V dc f = 1MHz
Low Level Output Voltage
0.6
V
Input Threshold Current High Level Supply Current Low Level Supply Current High Level Enable Current Low Level Enable Current High Level Enable Voltage (note 10) Low Level Enable Voltage Input Forward Voltage Input Reverse Breakdown Voltage
IFT ICCH ICCL IEH IEL VEH VEL VF VBR CIN
VF TA
3 7 9 -0.6 -0.8 2
5 10 13 -1.6 -1.6
mA mA mA mA mA V
0.8 1.75 5 .com 60 -1.4
V V V pF mV/C
t4U.com
Input Capacitance Temperature Coefficient of Forward Voltage Input-output Isolation Voltage (note 3) Input-output Insulation Leakage Current (note 3) Resistance (Input to Output) (note 3) Capacitance (Input to Output) (note 3) * All typicals at TA= 25C
DataShee
VISO
2500
VRMS
A
II-O
1
RI-O CI-O
1012 0.6
pF
RECOMMMENDED OPERATING CONDITIONS PARAMETER Input Current, Low Level Input Current, High Level Supply Voltage, Output Enable Voltage, Low Level Enable Voltage, High Level Fan Out ( TTL Load ) .com Operating Temperature
30/7/03
SYMBOL IFL IFH VCC VEL VEH N TA
MIN 0 6.3* 4.5 0 2.0 -40
MAX UNITS 250 15 5.5 0.8 VCC 8 85 C
DB91019-AAS/A2
A
mA V V V
*6.3mA is a guard banded value which allows for at least 20% CTR degradation. Initial input current threshold value is 5.0mA or less
DataSheet 4 U .com
www..com
SWITCHING SPECIFICATIONS AT TA = 25C ( VCC = 5V, IF = 7.5mA Unless otherwise noted ) PARAMETER Propagation Delay Time to Logic Low at Output ( fig 1 )( note4 ) Propagation Delay Time to Logic High at Output ( fig 1 )( note5 ) Propagation Delay Time of Enable from VEH to VEL ( note6 ) Propagation Delay Time of Enable from VEL to VEH ( note7 ) Common Mode Transient Immunity at Logic High Level Output ( fig 2 )( note8 ) Common Mode Transient Immunity at Logic Low Level Output ( fig 2 )( note9 ) SYM DEVICE t PHL MIN TYP MAX UNITS TEST CONDITION 25 45 75 ns RL = 350, CL = 15pF
t PLH
20
45
75
ns
RL = 350, CL = 15pF
t EHL
20
ns
RL = 350, CL = 15pF VEL = 0V, V EH = 3.5V RL = 350, CL = 15pF VEL = 0V, V EH = 3.5V IF = 0mA, VCM = 50VPP RL= 350,VOH= 2Vmin. VCM= 50VPP RL=350,VOL=0.8Vmax.
t ELH
20
ns
CMH
10000
V/s
CML
10000
V/s
t4U.com
NOTES:1 Bypassing of the power supply line is required, with a 0.01F ceramic disc capacitor adjacent to each isolator. The power supply bus for the isolator(s) should be seperate from the bus for any active loads. Otherwise a larger value of bypass capacitor (up to 0.1F) may be needed to supress .com regenerative feedback via the power supply. 2 Peaking circuits may produce transient input currents up to 50mA, 50ns maximum pulse width, provided average current does not exceed 20mA. 3 Device considered a two terminal device; pins 1, 2, 3, and 4 shorted together, and pins 5, 6, 7 and 8 shorted together. 4 The tPHL propagation delay is measured from the 3.75 mA level Low to High transition of the input current pulse to the 1.5V level on the High to Low transition of the output voltage pulse. 5 The tPLH propagation delay is measured from the 3.75mA level High to Low transition of the input current pulse to the 1.5V level on the Low to High transition of the output voltage pulse. 6 The tEHL enable input propagation delay is measured from the 1.5V level on the Low to High transition of the enable input voltage pulse to the 1.5V level on the High to Low of the output voltage pulse. 7 The tELH enable input propagation delay is measured from the 1.5V level on the High to Low transition of the enable input voltage pulse to the 1.5V level on the Low to High of the output voltage pulse. 8 CMH is the maximum tolerable rate of rise of the common mode voltage to assure that the output will remain in a high logic state (ie Vout > 2.0V). 9 CML is the maximum tolerable rate of fall of the common mode voltage to assure that the output will remain in a low logic state (ie Vout < 0.8V) 10 No external pull up is required for a high logic state on the enable input. FIG.1 SWITCHING TEST CIRCUIT PULSE GENERATOR ZO = 50 tr = 5ns 5V 1.5V tPHL tPLH 1.5V VOL IF Monitor 100 10% Duty Cycle 1/f < 100s
DataShee
IF 1 2 3 4 8 7 6 5 CL = 15pF
DB91019-AAS/A2
IF VO
0
5V RL VO
.com
30/7/03
DataSheet4 U .com
www..com
FIG. 2 TEST CIRCUIT FOR TRANSIENT IMMUNITY AND TYPICAL WAVEFORMS
VCC 8 7 6 5 VCM + -
VCM 0V VO VO
10V 90% 10% tr tf
IF 10% 90% A 5V VOL B VFF
1 2 3 4
5V RL VO
SWITCH AT A: IF = 0mA SWITCH AT B: IF = 7.5mA
PULSE GEN.
Forward Current vs. Forward Voltage 10 4 Forward current IF (mA) 2 1 0.4 0.2 0.1 0.04 0.02 0.01 1.0 TA = 25C Output voltage VO (V) 9 8 7 6
Output Voltage vs. Forward Input Current VCC = 5V TA = 25C
t4U.com
5 .com 4 3 2 1 1.2 1.4 1.6 0 0
RL = 1k RL = 350
Forward voltage VF (V) Low Level Output Voltage vs. Ambient Temperature VCC = 5.5V VE = 2V IF = 5mA High level output current IOH ( A )
1 2 3 4 5 Forward input current IF (mA) High Level Output Current vs. Ambient Temperature
6
0.8 Low level output voltage VOL (V) 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 0
1.0 0.4 0.2 0.1 0.04 0.02 0.01 0.004 0.002 0.001 0 10 20 30 40 50 60 Ambient temperature TA ( C ) 70 VCC = 5.5V VO = 5.5V VE = 2V IF = 250A
IO = 16mA
IO = 12.8mA
IO = 6.4mA
IO = 9.6mA
.com
30/7/03
10 20 30 40 50 60 Ambient temperature TA ( C )
70
DB91019-AAS/A2
DataSheet4 U .com

▲Up To Search▲

Price & Availability of ICPL2611

	To Download ICPL2611 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .